Allen-Bradley Repair
PowerFlex · ControlLogix · Kinetix
View repairs →Component-level repair of Mitsubishi FR-A800 / A700, FR-E800 / E700, FR-D700 / D800, FR-F800 / F700 and legacy FR-500 series drives. Free evaluation, written quote before any work, 2-year warranty. Ship it to us or drop it off in Lewisville, TX (Dallas–Fort Worth).
From a compact FR-D720S on a fan to an FR-A840 on a crane hoist — we repair the power section, control board and operation panel, then load-test the drive before it ships.
Mitsubishi's flagship vector drive on cranes, extruders, winders and machine tools. We repair the power section, control board and the built-in options, then load-test the drive.
Discontinued, but still installed across US plants. Repairing the FR-A740 keeps the panel, wiring and parameters as they are instead of re-engineering for an A800.
The most common compact Mitsubishi drive on conveyors, packaging and OEM machines. The E800 adds built-in Ethernet — we repair both generations.
Simple-speed drives for fans, pumps and small conveyors. Typical failures: input rectifier, DC-bus capacitors, output IGBTs and the switch-mode power supply.
Variable-torque drives for HVAC, water and wastewater. Long hours at full load age the capacitors and cooling fans — both standard repairs for us.
Older Mitsubishi drives with no factory support. Board-level repair is usually the only way to keep the original machine running without a retrofit.
A fault that comes back after a reset usually points to failed hardware. These are the ones we see most often on the bench.
Overcurrent during acceleration, constant speed or deceleration. If it trips immediately even with the motor disconnected, an IGBT or gate driver has failed. We replace the failed devices, not the whole power section.
Repeated overvoltage on deceleration with correct settings points to a failed brake transistor (E.BE), aged DC-bus capacitors or a faulty voltage-detection circuit.
Failed cooling fan, clogged heat sink or a degraded thermistor. We replace the fan, re-apply thermal interface, verify the sensor and run the drive at load.
Undervoltage trips on a healthy supply usually mean a damaged pre-charge circuit, input rectifier or failing DC-bus capacitors. Pre-charge and capacitor bank repair.
With the motor and cable tested good, these point to a damaged output stage or current-sensing circuit inside the drive. Repairable at component level.
Control board CPU fault, parameter storage error, a blank operation panel or a drive that won't power up. Switch-mode power supply and control board repair, parameters preserved where the drive allows it.
You know the price before we start. Nothing is repaired without your approval.
Ship the drive to us from anywhere in the US, or bring it to our shop in Lewisville, TX.
Bench diagnosis of the power section and control electronics, usually within 24–48 hours.
Fixed price and turnaround in writing. Approve it, or get the unit back.
Component-level repair, then a load test before return. 2-year warranty on the repair.
Our repair shop is in Lewisville, TX. If your plant is in the DFW area or North Texas, you can bring the failed drive in yourself — no packing, no freight, no waiting on a carrier.
Customers outside Texas ship to the same address; we repair Mitsubishi drives for plants nationwide.
Typical ranges. Your exact price comes in a written quote after the free evaluation. Repair usually costs 40–70% of a new drive.
| Mitsubishi drive | Typical repair cost |
|---|---|
| FR-D700 / FR-D800 / FR-E700 / FR-E800 (compact) | $300 – $800 |
| FR-A700 / FR-F700 / FR-F800 (mid-range) | $700 – $2,500 |
| FR-A800 (high-performance) | $800 – $3,500 |
| FR-A500 / FR-F500 / legacy | Quote after evaluation |
Rush 24–72h service is available for line-down situations. See rush service.
Tested, refurbished Mitsubishi units available for immediate purchase or exchange. All units carry our 2-year warranty.






Other Mitsubishi equipment and other VFD brands we repair.
Send it in or drop it off in Lewisville, TX. Free evaluation, written quote, 2-year warranty. Standard turnaround 5–30 business days, rush available.
Answers to the questions we get most about Mitsubishi drive repair.
FR-A800 and FR-A800 Plus, FR-A700, FR-E800 and FR-E700, FR-D700 and FR-D800, FR-F800 and FR-F700, plus legacy FR-A500, FR-F500, FR-E500 and FR-S500 drives. For Mitsubishi PLCs, HMIs and MR-J servo amplifiers, see our Mitsubishi repair page.
Typical ranges: compact FR-D / FR-E $300–$800, FR-A700 / FR-F700 / FR-F800 $700–$2,500, FR-A800 $800–$3,500. Evaluation is free and you get a written quote before any work. Repair typically saves 30–60% compared to a new drive.
Yes. Our shop is at 860 Hembry St, Suite 401, Lewisville, TX 75057, in the Dallas–Fort Worth area. Call (254) 254-0005 or request a quote first so we expect your unit.
Yes. Replacing an FR-A740 or FR-A540 with an FR-A800 usually means new wiring, new parameters and sometimes new options. Repairing the original drive keeps the machine as it is. Common repairs are the output IGBTs (E.OC1–E.OC3), DC-bus capacitors and the cooling fan (E.FIN).
E.OC1 is overcurrent during acceleration (E.OC2 at constant speed, E.OC3 during deceleration). If the fault returns with the motor disconnected, the drive's output stage has usually failed and needs repair.
Standard turnaround is 5–30 business days; rush 24–72h service is available for line-down situations. Every repair carries a 2-year parts and labor warranty and is load-tested before it leaves the shop.
No. Flexa Systems is an independent repair company, not affiliated with Mitsubishi Electric. We repair Mitsubishi drives at component level and back the work with our own 2-year warranty.
Mitsubishi Electric and FREQROL are trademarks of Mitsubishi Electric Corporation. Flexa Systems LLC is an independent repair company and is not affiliated with, endorsed by, or authorized by Mitsubishi Electric.
Component-level repair for every major industrial automation brand — including discontinued and obsolete systems.
PowerFlex · ControlLogix · Kinetix
View repairs →SINAMICS · S7 · SIMATIC
View repairs →Drives · Servos · Motion
View repairs →ACS · ACH Series
View repairs →CNC · Servo · Spindle
View repairs →RX3i · RX7i · 90-30 · VersaMax
View repairs →590 DC · 690 AC · 890 Vector
View repairs →Drives · I/O Systems
View repairs →VLT · FC Series
View repairs →FRENIC · MONITOUCH · FALDIC
View repairs →Sysmac · NJ · NX · CS1
View repairs →