Siemens Repair
SINAMICS · S7 · SIMATIC
View repairs →Component-level repair of Allen-Bradley PLC processors, power supplies, communication and I/O modules: ControlLogix, CompactLogix, SLC 500, MicroLogix, PLC-5 and Micro800. Your program is backed up before any work. Free evaluation, written quote, 2-year warranty. Ship it to us or drop it off in Lewisville, TX (Dallas–Fort Worth).
Processors, chassis power supplies, EtherNet/IP and DH+ communication modules, and analog and digital I/O — we repair the module and test it in a live chassis before it ships.
Processors, communication bridges, I/O and power supplies on the plant's main control systems. Repair is the fast way back when a spare isn't on the shelf.
CompactLogix controllers and I/O on machines and skids, including 5380 controllers on the 5069 platform.
Still running thousands of US machines. Migrating to CompactLogix means rewriting the program — repair keeps the machine as it is.
Compact controllers on pumps, conveyors and small machines. Power supply, I/O and communication-port repair.
Legacy PLC-5 processors and 1771 I/O on older lines. Board-level repair keeps a working system running without a full conversion.
Micro820 / 850 controllers and distributed I/O adapters and modules in the field.
These are the failures we see most often on Allen-Bradley PLCs on our bench. Every repair starts with a program backup when the processor allows it.
The processor won't go to run, or faults again right after clearing. We find the hardware cause — memory, power rail or a failed component — and repair it.
SLC 500, PLC-5 and older MicroLogix keep the program in battery-backed RAM. When the battery or holding circuit fails, the program is lost. We repair the circuit and can load your backup.
No LEDs on the chassis. Chassis power supplies (1746-P2/P4, 1756-PA72, 1769-PA4) are a common failure — capacitors, regulators and input protection repair.
Lost EtherNet/IP, DH+, DH-485 or RIO connection while the network checks out. We repair the port and the communication module.
Dead inputs, outputs stuck on or wrong analog readings. Channel-level repair on digital and analog I/O modules, tested in a chassis.
Modules that work in one slot but not another, or intermittent faults on vibration. Connector, backplane and chassis repair.
You know the price before we start. Nothing is repaired without your approval.
Ship the module to us from anywhere in the US, or bring it to our shop in Lewisville, TX.
Bench diagnosis, usually within 24–48 hours.
Fixed price and turnaround in writing. Approve it, or get the unit back.
Component-level repair, then a chassis test before return. 2-year warranty on the repair.
Our repair shop is in Lewisville, TX. If your plant is in the DFW area or North Texas, you can bring the failed unit in yourself — no packing, no freight, no waiting on a carrier.
Customers outside Texas ship to the same address; we repair Allen-Bradley PLCs for plants nationwide.
Typical ranges. Your exact price comes in a written quote after the free evaluation. Repair usually costs 40–70% of a new unit.
| Allen-Bradley PLC | Typical repair cost |
|---|---|
| SLC 500 processors & modules | $300 – $1,500 |
| CompactLogix controllers & modules | $350 – $1,800 |
| ControlLogix controllers & modules | $450 – $2,500 |
| MicroLogix, PLC-5, Micro800 & I/O | Quote after free evaluation |
Rush 24–72h service is available for line-down situations. See rush service.
Tested, refurbished Allen-Bradley PLC units available for immediate purchase or exchange. All units carry our 2-year warranty.








Model pages and other Allen-Bradley equipment we repair.
Send it in or drop it off in Lewisville, TX. Free evaluation, written quote, 2-year warranty. Standard turnaround 5–30 business days, rush available.
Answers to the questions we get most about Allen-Bradley PLC repair.
ControlLogix 1756 controllers, communication, I/O and power supply modules; CompactLogix 1769 and 5069; SLC 500 1746/1747; MicroLogix 1000, 1100, 1200, 1400 and 1500; PLC-5 1771/1785; Micro800; and POINT I/O and FLEX I/O.
Typical ranges: SLC 500 $300–$1,500, CompactLogix $350–$1,800 and ControlLogix $450–$2,500, depending on the module and the failure. Evaluation is free and you get a written quote before any work. Repair typically saves 30–60% compared to a new module.
Yes. Our shop is at 860 Hembry St, Suite 401, Lewisville, TX 75057, in the Dallas–Fort Worth area. Call (254) 254-0005 or request a quote first so we expect your unit.
We back up the program before any work whenever the processor allows it, and restore it after the repair. On battery-backed processors (SLC 500, PLC-5, older MicroLogix) we recommend sending your own backup too, in case the memory was already lost.
If the machine runs well and only a module failed, repair is faster and much cheaper: a migration means rewriting the program, new I/O wiring and testing. Repair keeps the machine as it is.
Standard turnaround is 5–30 business days; rush 24–72h service is available for line-down situations. Every repair carries a 2-year parts and labor warranty and is tested before it leaves the shop.
No. Flexa Systems is an independent repair company, not affiliated with Rockwell Automation or Allen-Bradley. We repair Allen-Bradley PLCs at component level and back the work with our own 2-year warranty.
Allen-Bradley, ControlLogix, CompactLogix, SLC, MicroLogix, PLC-5 and Rockwell Automation are trademarks of Rockwell Automation, Inc. Flexa Systems LLC is an independent repair company and is not affiliated with, endorsed by, or authorized by Rockwell Automation.
Component-level repair for every major industrial automation brand — including discontinued and obsolete systems.
SINAMICS · S7 · SIMATIC
View repairs →Drives · Servos · Motion
View repairs →ACS · ACH Series
View repairs →CNC · Servo · Spindle
View repairs →RX3i · RX7i · 90-30 · VersaMax
View repairs →MELSEC · FR Series
View repairs →590 DC · 690 AC · 890 Vector
View repairs →Drives · I/O Systems
View repairs →VLT · FC Series
View repairs →FRENIC · MONITOUCH · FALDIC
View repairs →Sysmac · NJ · NX · CS1
View repairs →