Parker 690+0025/230/1BS | Repair & Stock
Parker 690+0025/230/1BS | Repair & Stock
Parker 690+0025/230/1BS | Repair & Stock
Parker 690+0025/230/1BS | Repair & Stock
Representative photo only, the picture does not illustrate the actual unit and is provided for reference purposes only
US Seller and services provider

Parker 690+0025/230/1BS | Repair & Stock

Brand new, original packaging:
$
In stock: 1
Make the order
Request repair
Field Service Request
Call +1 (254) 254-0005 for a Quote
Delivery
Estimated delivery time for selling products 3-10 days.
Regular repair estimated turnaround time 5-20 days.
Hot rush repair turn around time 1-5 days.
📦 Shipping from Texas Warehouse
 Serving All 50 States | Based in Texas | Units In-Stock & Ready for Fast Turnaround

Parker 690+0025/230/1BS | 25 HP (18.5 kW) 230V VFD

  • Series: Parker 690+ AC Variable Frequency Drive
  • Power Rating: 25 HP (18.5 kW)
  • Input Voltage: 230V ±10%, 50/60Hz
  • Enclosure: NEMA 1 (UL Type 1 – general-purpose indoor use)
  • Braking Setup: Brake switch fitted (external resistor required)
  • System Board: Included

Common Problems We Fix with This Drive 🛠️

  • ⚡ Overvoltage: usually caused by aggressive deceleration without braking resistor
  • 🔋 Undervoltage: from unstable input, missing phases, or internal PSU faults
  • 🚨 Overcurrent: results from improper motor tuning, shorted windings, or sudden torque changes
  • 🌡️ Heatsink trip: blocked airflow, dead fan, or ambient temp exceeding limits
  • 🛑 Stall faults: too much mechanical load or improperly set stall thresholds
  • 🔥 Brake resistor overload: frequent decel events or undersized resistor
  • 💣 Brake switch burnout: happens after continuous high-cycle braking
  • 📡 COMMS timeout: from parameter config issues or interference on signal line
  • 🛑 STO fault: safety board signal issues or failed STO input
  • 🔁 Internal comm errors: logic board and power section desync, often from firmware failure
  • 🎯 Encoder fault: feedback loop out-of-range or bad encoder connection
  • ⚠️ Current limit exceeded: motor acceleration or torque profile too aggressive
  • 🔌 24V supply drop: external short or excessive load
  • ⚠️ Phase fail: due to input wiring loss or internal trace failure
  • 💥 DESAT overcurrent: blown IGBT, faulty gate driver, or heavy load arc fault
  • 🔄 Ripple voltage issue: common with failing DC bus capacitors or power phase imbalance
  • 🧨 Brake fault: resistor path overcurrent or open circuit
  • 🚀 Overspeed: bad feedback tuning or mechanical instability
  • 📏 Analog input issues: sensor wiring or signal calibration mismatch
  • 🐌 Overcurrent at low speed: boost configured too aggressively or underloaded
  • 🌡️ Motor overtemperature: blocked ventilation, thermistor trip, or mismatched motor

Why Flexa Systems?

Flexa Systems specializes in component-level repair and full replacement for the Parker 690+0025/230/1BS drive. If you’re seeing fault codes, motor stalls, or complete power loss, we’ll get it running again. We service clients across the U.S. from our Texas-based repair hub with rapid turnaround and fully tested units in stock.

📌 Important Notes

Please contact us to confirm your exact requirements or verify application compatibility.

Note: Pricing and availability vary depending on unit condition, configuration, and current stock levels.

Flexa-Systems LLC is not officially linked as a dealer, agent, or affiliate of any designers, brands, or manufacturers whose products are showcased on www.flexa-systems.com. Any mentioned trademarks, brand names, or logos serve solely for identification purposes and remain the registered trademarks of their respective owners, who maintain their rights. The inclusion of these trademarks, brand names, or products on our website does not imply any affiliation or endorsement by the company, trademark, or brand."

Flexa Systems' (2) Year Limited Warranty

Our Warranty
Flexa Systems LLC offers a comprehensive warranty program to ensure peace of mind for your industrial equipment investments. Limited Warranty Coverage
  • Equipment Repairs:
    We provide a 2-year limited warranty on all industrial equipment repairs performed by our technicians. This warranty demonstrates our commitment to the quality of our workmanship. If a repaired item fails due to a covered defect, we will re-repair it free of charge.
  • New Equipment Sales:
    New equipment carries the original manufacturer's warranty. We will gladly facilitate warranty processes with the manufacturer on your behalf.
  • Refurbished Equipment Sales:
    Refurbished equipment comes with a 2-year limited warranty from Flexa Systems LLC, covering defects in materials and workmanship related to our refurbishment process.
Warranty Exclusions (Applies to both repair and refurbished equipment warranties)
This warranty does not cover:
  • New damage caused by liquid, dust, or object contamination
  • New damage caused by mechanical impact, improper installation, incorrect accessories, voltage or current issues, overloading, or overheating.
  • Severe scratches on the unit
  • Broken display (if applicable)
  • Impact or dropping of the unit
  • Removal or deterioration of the warranty sticker
  • Opening the product's cover (if applicable)
Warranty Claim Process
To initiate a warranty claim, please contact our customer support team. Repair or replacement under warranty can take up to 31 calendar days.
Important Note: We repair industrial equipment from various brands; however, we are not a dealer, agent, or affiliate of any specific designers, brands, or manufacturers.
SKU: 32038 Categories: ,
Cart Close
Updating…
  • No products in the cart.

Continue shopping